DTMF Controlled Robot without Microcontroller
DTMF is the acronym for
Dual tone modulation frequency. Robotic vehicle based on DTMF technology is
explained in this article. Here is a circuit that operates the robot without
using a microcontroller. This circuit consists of simple ICs.
When a key is pressed from
our mobile, it generates a tone combination of two frequencies from our keypad.
In the two frequencies, one is high frequency and another one is low frequency.
This frequency can be decoded by the decoder IC into binary sequence.
DTMF Based Robotic Vehicle Circuit Principle:
DTMF based robotic vehicle
circuit consists of DTMF decoder IC, driver IC l293D IC and motors.
DTMF decoder IC used is
HT9107B. It has 18 pins. Tone from DTMF encoder is given to the DTMF decoder
IC. The decoder IC internally, consists of operational amplifier whose output
is given to pre filters to separate low and high frequencies. Then it is passed
to code detector circuit and it decodes the incoming tone into 4bits of binary
data. This data at the output is directly given to the driver IC to drive the
two motors. These motors rotate according to the decoded output.
If
the button pressed from mobile is ‘1’, it gives a decoded output of ‘0001’.
Thus motor connected to the first two pins will get 0 volts and second motor
will have 5 volts to one pin and 0 volts to the another pin. Thus second
motor starts rotating and first motor is off. So, robot moves in one direction
either to left or right. If the robot is to rotate forward or backward then the
binary value should be either ‘0101’ or ‘1010’.These values indicate that two
motors rotates in the same direction i.e. either forward or backward. The
following table gives the low frequency, high frequency and binary output value
of each button pressed in the keypad.
DTMF Decoded Frequency
Output Table
Circuit
Diagram of DTMF Controlled Robotic Vehicle without using Microcontroller:
DTMF Mobile
Controlled Robot without Microcontroller
Circuit
Components:
·
DTMF Decoder IC (HT9107B)
·
Motor Driver IC
·
Motors
·
Capacitors – C1 to C4
·
Crystal Oscillator
DTMF Controlled Robot Circuit Design:
The main components of the
circuit are DTMF decoder IC, motor driver IC and motors. The decoder IC used
here is HT9107B IC. The second pin of decoder IC is an inverting pin of the
operational amplifier.
Tone is applied to the IC
through a series of capacitor and resistor. The output of the Op Amp is feed
back through GS pin of the IC. An external crystal is connected to the 7th and 8th pins of the IC.
Motor driver IC used is
L293D. It has 16 pins. 2, 7, 10, 15 pins are the inputs of motor driver IC
connected from output pins of the decoder IC. The output pins are 3, 6, 11, 14.
These pins are connected to the two motors of robotic vehicle. 8th pin is connected to the 5v. Vss is the
input voltage with which the motors runs. Motors cannot be driven with 5Vof
microcontroller. So, a driver IC is used to amplify this voltage. VSS pin
provides this voltage.
How DTMF based Robotic Vehicle Circuit
Works?
·
Arrange the robot mechanically i.e. connect the wheels to the
motors, place the circuit on the robot with a mobile fixed to it.
·
Now press ‘5’ from your mobile, robot starts moving forward.
·
Now press ‘0’ from your mobile, robot starts moving backward.
·
Now press ‘2’ to rotate the robot in left direction.
·
Now press ‘8’ to rotate the robot in right direction.
DTMF Controlled Robotic Vehicle Circuit
Applications:
·
DTMF robot with slight modifications can be used in industrial
applications.
·
DTMF robot with human detector sensor can be used at the time of
disasters like earth quake to detect the human under buildings.
·
DTMF robot with camera can be used in surveillance systems.
Limitations of DTMF Controlled Robotic
Vehicle :
·
DTMF robot may not work properly if it is operated with another
mobile when there is no signal.
·
Mobiles with particular jacks are only used.
http://www.hubcity.net
No comments:
Post a Comment